Wednesday, November 29, 2017

My First Tablesaw


Being aware of the dangers of a table saw are extremely important.  In this video, I ramble about things I checked on my saw before getting started.
Read More »

Friday, November 17, 2017

Radio Flyer Wagon Wheel Upgrade




This project began with me stating "I'll be damned if I pay $25 per wheel for an upgrade from Radio Flyer!".

And down the rabbit hole I went!







Materials Needed/Used:


  • Beer
  • Mallet
  • 10 inch pneumatic tires 
  • WD-40
  • More Beer
  • 5/8 (Outer Diameter) 7/16 (Inner Diameter) Vinyl tubing 
  • 7/16 Push Nuts
  • Needle Nose Pliers
  • Razor blade
  • 1/2 inch PVC


The short of it: Remove old tires, use the vinyl tubing as a spacer to fit the 10 tires onto a 7/16 axle.


The Breakdown:

Removing the old tires is easy.  You can break the push nuts off or save them by twisting them as if you are unscrewing them.  Saving them could save you the time of locating new ones and it one less thing to track down.

Old & new Push Nut

~1/2 inch space where old spacer attached




Spacer & Tire removed from back

Once they are off you can start dealing with the mispaired axle size and tire bore.  Although on the Radio Flyer website they are listed as 1/2 inch axles for this model, they are not 1/2 inch but 7/16.  If you then measure most tire bores, you will discover they are generally 5/8.  And if you are really good at math, you might realize 5/8 is not the same as 7/16.  Kudos.

Axle size

Rear Axle

I tried searching for spacers, and failed.  The best I could find was some vinyl tubing with the correct inner and outer sizes.  However, I knew it would be a tight fit it I got the exact size.   A smaller size might work as well and be easier. Hindsight right.



After some amazing calculations and beers, I arrived at the spacer sizes I need to keep the new larger wheels from rubbing.  I came up with PVC spacers the measured 3/4 inch for the back axle and 3/8 for the front axle.  There is room for error and room for play, but mileage may vary.

This next part requires equal parts WD-40 and Beer.  Getting the vinyl spacer into wheel bore and then onto the axle.  I cut vinyl tubing to about 2 5/8 inches.  In order to make this tight squeeze a little easier, I beveled the inside and outside of the tubing, and then sprayed everything with WD-40.  Be sure to place your 3/4 PVC spaces on the axles first before getting the tire on.  The WD-40 made it easier to slide the tubing into the wheel bore, and then by spraying the axle, it helped to slide the tire+tubing.
Inserting tubing first

3/4 PVC spacer with ~2 5/8 rear axle

Rear axle with tubing and spacer


Rear axle vinyl tubing removed

While the back tires when on like a prophylactic in Amsterdam, the front was not as easy.  First, this model of Radio Flyer has the two independent front axles.  So you will have to either use something to brace it, or build a wedge to keep it from spinning,  I went the hard route and just held it with my hands.  Again, make sure you put on the 3/8 PVC spacers first.  Secondly, there is not alot of play room on this axle and it has a flare that held a washer in place for the other wheels.  It took a little work but I was able to get enough of the wheel on with enough tubing.
Front Axle with Flare

One tire on front axle 
Front axle with tubing


It is worth mentioning, that is you use this method, you may not need the 3/8 PVC spaces on the front.  The fit is fairly tight.

Now, to make it nice an trim, take a razor blade and carefully trim off any excess vinyl tubing.  Do be cautious on this step as you are cutting in an unusual position.

Now place you push nuts back on and you are ready to cruise!




Be Aware:  These tires work great off-road.  I'm not going back.  However, if you mainly use your wagon on the street, be warned.  On the street, I've noticed that the front axles will get into a tug of war and cause a synced wobble. Not sure it has to do more with alignment, or just the fact that the front are free.  Sticking a child in the front may put enough weight down to fix the issue.


And that's it. Not too bad for an off-road wagon.  If all else fails, you can always put back on the old wheels.  Good luck out there, and if you have any tips to share, be sure to leave them in the comments.  Thanks again!


Read More »

Sunday, October 22, 2017

DIY Playboard / Toybox Top



It is a simple board, but the boy loves it.  I mean c'mon, give them a box and there are activities for days!  I'll give you a quick rundown on the build, but you make the final as to how complex or simple you want to go.

Materials Needed:
3/4 inch high grade plyboard (Cabinet grade)
1/4 inch panel board
Router
Jigsaw
Drill bit (I used 1 inch hole saw bit)





1. Cut board to size to fit the top of the toy box.  Then round the edges with your jigsaw.

2. For ease of flipping and holding, I drilled and jigsawed hand openings at each end.  First I drilled two holes about 6 inches apart using my hole bit.  Then using the jigsaw, I cut the remainder of the hole for the handle.



3. Using a straight bit for my router, I first cut the deeper part of the lake.  Take your time and make sure you go against the rotation of your router. Then shorten your bit and finish the rest of your lake.

4. I then cut a few a few shapes to make hills.  Start with the larger base and then start adding to the nest levels.  You can get crazy or go simple, your choice.



5. Glue everything in place with wood glue.

6. One side will was requested to be white.  I left this side to be flat so it could also be a Lego work table.  

7. I used spray paint, but any paint will work.  I also taped the edges to give that wood look to the edges. It was a nice pop.



8. I went with a normal green for the landscape, and two blues for the water.  I went simple, but you could really get detailed here.  I had to talk myself out of it.  I really love to make more work for myself.




Overall, it was a fairly quick project that has already gotten tons of use.  There has been many Lego battles and projects on the board.  Though for some reason, I really want to drill a small hole and make a mini-golf course.  

Read More »

Monday, October 9, 2017

My Absence



Hello my fellow hobbits,
My apologies for being absent for so long...though I have been active on my Youtube Channel.

The Bearded Hobbit

It has been a non-stop circus here.  October and November are my busiest months of the year.  So many trips and to add to it we are just now getting the house in order.  Though my Honey-Do List does continues to grow.  I've got some videos and photo blogs in the works and will be loading those ASAP.  I have real work to finish first.  I have an insect survey I did back in August right before the hurricane that I must key out. Muy Importante.

So what's in the works?

  • It is Texas Renaissance Festival Time, so I'll have some cosplay builds
  • And because we take the kids to the Renaissance Festival, I have a wagon upgrade build
  • I will also be tackling my first dining table, due by Thanksgiving
  • Toybox play "lid"

But give me time, I got my bugs to identify, and an archery tournament that my son and I are participating coming up.  So I'll be back as soon as I can.
Read More »

Thursday, August 10, 2017

A Journey Beyond the Shire



I know it’s been awhile since I last posted.  We have been in the middle of a move for the past 3 months.  And by middle of a move, I mean, sold our house, moved into an apartment, and then into our new home.  This was not by design but by circumstance.  Let me tell you, this Hobbit has ingested many an ale and cider through this ordeal.  Had I access to pipe weed, I think I would have pulled a classic Merry and Pippin and toked away. I will not bore you with details but will give you a short tale of how everything fell apart but came to together in the end.

Leaving the Shire
We found the home we wanted.  It met most of the requirements and wants, only missing a few.  This was good.  We placed an offer on the house, which was accepted.  We then placed our home on the market.  We soon had on offer on our home which allowed us to move forward in the many, many steps to purchase a new home.  And then came the inspection.  This was a new home we were purchasing, new construction.  As with any new home, we expected an easy inspection.  There were some issues spotted by our very thorough inspector.  It was upon his recommendation we get a roofer out there to inspect it, so we did.  Let me be frank here, when a Christian based company has one of its top employees tell you something is “shit”, you listen.  This is the exact description I received about the roof ON A NEW CONSTRUCTION.  If ever you are buying a home, new or old, and you are asked if you want an inspection answer in your best Severus Snape “Always”.

The Apartment
As a result of the terrible inspection and multiple red flags, we moved on.  We sold our home and had to move.  So without knowing how long it would take to find a home, we signed a short lease hoping to find something soon.  The apartment wasn’t that great, though they were attempting to update.  I have moved all over East Texas and lived in some crappy places, so this really didn’t bother me.  My concern was my wife and kids.  How is this going to impact them?  My wife and I try to be as cognizant of how our actions and emotions affect our children.  I gotta say I worried for nothing, they were champs.  Going from a three-bedroom to a two-bedroom apartment was a bit of an adjustment, but we made due. I was still able to grill a bit, thanks MacGuyver. Kids had a play place under the stairs complete with the d├ęcor of Christmas lights.  It was a pretty cool hobbit hole.  And then we found….

Hobbit Farms
The journey to get here was tiresome. We place offers on homes that were not accepted, spent money on inspections, only to find issues we were not willing or financially able to overlook.  We are by no means “those” house hunters.  And then everything happened.  We placed a contract on a home, only to be told by the builder, they couldn’t cancel the last contract.  So what do we do, wait?  And then the phone rang.  Our realtor got the scoop on a home that had just went back on market and it was everything we were looking for.  We walked through and put an offer in the same day.  And I am typing this now from that very home.  I have land and room to play with the kids.  I cannot complain.  So look forward for post from the new area with reviews on outdoor gear and tools, as well as tools.  I have a small forest to clear.  Upon signing up for home maintenance material, I decided to call the home Hobbit Farms.  I have no vegetables or animals yet, but I suspect you will be seeing those i
Read More »

Wednesday, June 28, 2017

Gear: Kid-O-Bunk



My family travels. Quite a bit.  When we do visit friends and family there is often not much room to accommodate us plus kids and sometimes the dog.  I'm sure many of you parents out there can relate.  Travel can be cramped.  I happened upon the idea of looking for some type of bunk cot after seeing some that the Red Cross had set up in a disaster center.  It did not take me long to come across Kid-O-Bunks.



The cool thing about these beds is that they can stack.  Safely.  This really helps in saving space if you are in a cramped room.  When we go camping this saves a lot of room for gear, particularly if it rains and we have to take cover in the tent.





When using the bunks, there is a special leg that is attached to the bottom of the top bunk.  These legs pop into the rounded black "wheel" at each of the four corners. (See Video)  These bunks are then lashed together at each end using the supplied strapping to keep tension between the two bunks.



But, you don't have to stack them, you can use them as regular kids cots.  We have used this configuration during many sleepovers. Kids really love to sleep in these.

Some Specs:

  • 200lb weight limit for each cot
  • 5ft is about the max height for comfortable sleeping
  • Each cot is about 45lbs
  • 18in space between top and bottom bunk
  • Very stable due to width of base
  • Side storage to keep all their crap
               More specs on Amazon



I really have only good things to say about the bed.  However, I will point out a few things to be aware of when using the beds.  
  • Construction. With anything, make sure you have put it together correctly.  The bed can take a minute to put up, so don't expect to do it in a hurry.  If parts are not pushed tightly together or placed correctly, you risk collapse.  I wouldn't expect anything major if that happened as the tension still holds it together quite well.

  • Camping in the Cold.  It's easy to forget the comfort of your little ones.  Remember, these are off the ground, so just like an air mattress, they can get cold underneath.  Make sure you add a blanket or layer of some kind to keep them warm.

  • Sound. Dear god these things can be louder than a Sunchips bag!  So, our kids usually use sleeping bags when sleeping on these.  The friction between the bags and the cot material is noticeable.  It has woken me up a few times.  The solution is simply using blankets or placing a small blanket underneath the sleeping bag.  Doing this actually helps to solve the "Sleeping in the cold" problem.


All in all, I highly recommend these.  Though the price can be steep, you will question as to why you didn't buy them sooner.  

*Any recommended or referenced items you purchase through links helps to support this page

Purchase Links



Read More »

Friday, June 16, 2017

Ticks: The Vampires You Should Be Concerned About




If I haven't freaked you out with my last article about Poison Ivy, let me try again.  Just kidding...maybe.  First, tick bites can be prevented with a little information, which I will give you below.  Don't let this, or any other outdoor risk, scare you or your kids from getting outside.  Risk is an issue I love to talk about in my courses.  The riskiest thing you and your child do every day is getting inside a car.  Getting outside and injured, or getting a tick is low on that spectrum.  I have stories later on...

This is a tick.  Small aren't they.


Ticks. Nature's little vampires.  Ticks are in the Arachnid group and are easily identified as being small and flat with 8 legs. For the purpose of this blog, I will not be going into identification.  It doesn't matter which tick you have on you, that's the tick you don't want on you.


Tick Myths

  • Ticks find you by smelling your blood
    • False - They sense the carbon dioxide from you breathing, your heat and movement.

  • You can feel a tick when it bites you
    • Really...if that was the case, then there would be no tick-borne disease in humans.  They use secretions to "numb" the site of the bite. There is only a small fraction of people that can actually feel them bite. Very small.

  • Ticks jump out of trees
    • They can't jump.  They are found in tall grass and brush.  If you find one on your shoulder, it's because it crawled that far up your body. Just like your ex- literally a "Stage 5 Clinger".

  • Remove ticks by burning them
    • Not a good idea, this could cause more problems, including causing infection.

  • Ticks burrow into your skin
    • No, that's chiggers, ticks only insert their mouthparts.  Think mosquito on steroids.

  • I only have to worry about ticks in the Spring and Summer.
    • I wish.  Though depending on temperature, some ticks do go dormant in the cold month, but there are a few species (Adult Deer Ticks) that are still active through winter.


How To Avoid Ticks

The easy answer to this is DEET (20% +) or Lemon Eucalyptus Oil (but it must contain OLE "oil of eucalyptus" and/or PME).  Spray the hell out of your socks, shoes, pants legs, waistline, and shirt.  It also helps tremendously to tuck your pants into your socks and shirt into your pants.  Not fashionable I know, but it works.  This trick has saved from numerous critters, including chiggers.  If you are concerned about bathing in DEET, I get it.  For me, I'd rather risk the DEET than the disease from a tick.  But you have another alternative in the Lemon Eucalyptus Oil, however, you must reapply frequently! Don't forget!



The other way to avoid ticks is to avoid their habitat.  Well, the whole of the outdoors is their habitat and you can get a tick anywhere.  However, the most likely place is tall grass.  They like to hang out at the tips of vegetation and crawl/grab/fall on organisms as they pass.  Ticks cannot jump nor can they fly, so you have to really brush against them for them to attach to your clothing.  If you wear light-colored clothing, and spot check frequently, you have a greater chance of seeing them before they get to you.

And just because an area was tick free last week, does not mean it is this week.  Tick outbreaks are really interesting as they are like land mines.  You could be hanging out with a friend hiking and be two feet away from one another and they end up with ticks everywhere and you don't have any.  When ticks hatch from their eggs, they don't move very much from their original location, so you end up with many ticks in a confined area.



Sweet Baby Jesus, I Found A Tick On Me




You should always do a tick check on yourself. Look everywhere and I mean everywhere. It's better if someone else can assist you because they can see places you can't.  And if you are tick free...well you and your partner are more than likely naked already...you know....celebrate.  Anyway, what if you find a tick. BURN IT, MURDER IT!  Actually, no don't do that.  Never try to burn it, squeeze it, pour something weird on it, etc.  Use Tweezers or a Tick Key to remove the tick.  With tweezers, grab the tick as close to the head as you can and pull straight out.  Don't twist.  Make sure you are not squeezing the abdomen, the round back part, as there is a possibility you could squeeze some yucky tick juice into yourself.



Remove the tick as soon as possible.  Leaving the tick in until it dies or falls off is a really bad idea.  Current research has shown that Lyme disease, or any other, can be transmitted within hours of the initial bite.

Note: Peppermint oil.
Ok, I have heard of people pouring peppermint oil on a tick and it detaches.  These are more than likely ticks that have just attached. Once ticks are on you for a bit, they are actually kinda cemented into your skin due to the secretions of the tick.  This is why it hurts to pull a tick out.


Ticks and Disease

Most ticks do not carry any disease, so the odds are in your favor.  There are many different species of ticks, and with each species, they can only transmit certain diseases to humans.  Most of these diseases are bacterial with a few viral thrown in for good measure.  The most notable of course is Lyme disease.  Lyme accounts for roughly 70% of vector-borne disease, while all vector-borne is 95% from ticks.  Mosquito-borne is only about 6%.  Bet that DEET is looking pretty good right now.

CDC 2014

CDC: Reported Cases of Lyme Disease in 2015


At the very least, you should place the tick in a Ziploc bag, along with some information about where you were when you got the tick, and the date. Toss that bad boy in the freezer and wait.  If you begin to have symptoms in the next month, you have the tick which can be identified and tested. There are many different diseases, many cause a rash and fever.  Check out the CDC website for more specific symptoms.


Characteristic "Bullseye" rash of Lyme disease.
Courtesy of the University of Iowa.

Important: Just because a distribution map doesn't show the disease in your area, does not mean that it is not there!  Any scientist/doctor will tell you that these are based on historical data and that data changes, just as the ecosystems and landscape changes.

My advice goes one step further.  Here in Texas, and many other states, you can send in your live tick and they will test it.  This is often a free service from your state's health department.  They can then give you exactly what species of tick it was and what, if any, disease it carried.  This is important for two reasons:

  1. It's cheaper to test the tick than you.
  2. There is a possibility that a tick is carrying one than one infectious agent. and
  3. These are important data sets that you are contributing towards.  Some keywords for your search to submit a tick "State", "Health Department", and "Tick" or "Zoonosis".


I have had many ticks, and I've just recently started submitting them to the state for testing.  So far nothing has come back other than a few "hhmmm, that's interesting" comments.  I've had ticks that have had some bacterial relatives to the more nasty diseases, but no illness so far.  With that being said, the CDC estimates there are many cases of Lyme disease not being reported and many going undiagnosed or misdiagnosed. There are also many other diseases from ticks, some nasty, others not too bad.  The Powassan virus is one to be concerned about, as it can be fatal, or cause severe brain damage....and there is no treatment.


 It would be best to err on the side of caution and be stringent in your tick prevention methods.  And if you do get a tick, be sure to submit it for testing.

If in Texas, This is the link for submitting your tick for testing.
http://dshs.texas.gov/idcu/health/zoonosis/tickBites/



Recommended or Referenced Items:
      


*Any recommended or referenced items you purchase through links helps to support this page.

Reference:

True Facts About Lyme Disease
https://imgur.com/gallery/qwgtU/comment/1054392895/1

https://imgur.com/gallery/yKolQ

CDC Lyme Disease
https://www.cdc.gov/lyme/index.html

Youtube: CDC Emerging Tickborne Disease
https://www.youtube.com/watch?v=al5EM3yh--0

.
Read More »

Sunday, June 4, 2017

How to Identify Poison Ivy



Well kids, it's that time of year again! Mosquitoes and Poison Ivy.  Yes, I know, these guys are here in Texas year around.  For us in the southern U.S. states, it's full blown summer, kids are out of school and its time to get out of the house and enjoy the weather before it becomes unbearable.

So while out and about you must know your enemy.  Can you identify poison ivy?  It can be tricky for sure.  If I learned anything from my Plant Taxonomy course it's you never pick a plant your professor tells you to pick up.  Thanks, Dr. Williams.  The second thing is that plants can look very different based on the amount of sunlight, soil, season and geographic location.  I will be using examples I have come across here in Texas, most of these characters will be similar to other regions throughout.

So here we go:

First, should you even be worried?

From the USDA, if you live in these states, then yes.


But if you are in a white state, you don't get off that easy.  There is still poison oak...it's in all states and in Canada.

Alright, you may remember the little rhyme "Leaves of three, let them be".  It's not bad advice at all really, it can help you eliminate many of the plants that are often mistaken for poison ivy.  But let's dig a little deeper and really pin down the identification.  Otherwise, you won't be able to go outside for fear of poison ivy, because there are a lot of harmless three leaf plants

Generally, the two outer leaves of poison ivy will have a notched side and smooth side.  The notched side will be facing outward while the smooth side will be facing the middle leaf.  Sometimes the notch is very prominent, and sometimes it is hardly visible.  The trick though is that difference in leaf sides.  


The middle leaf....well, it's highly variable.  Sometimes it's smooth on both sides, sometimes is has a notch on both sides.  So there ya go.



Two plants I often see mistaken for poison ivy are young Virgina Creeper and young Dewberry plants.  Notice that Virgina Creeper has too many leaves and Dewberry has too many notches, or teeth along its leaf edge.  Dewberry also has spine or thorns on its stem.  Poison Ivy will not have thorns.

Virginia Creeper

Dewberry


Poison ivy can also be in a vine form.  It's like a Pokemon.  Not only do you need to look on the forest floor, but also climbing up a tree.  Sometimes you will see the leaves, sometimes not.  I would say look for fuzzy looking vines...but even then it may not be poison ivy, so just error on the side of caution and leave it alone.

Ok quiz time:

Can you spot the poison ivy?

Find the Poison Ivy

Solution 1

Well done.  One more!

Where is the Poison Ivy?

It's everywhere!

Is this poison ivy?

Nope!

A few more features to look out for, but may not be as definitive as the leaf shape.

  • You may also see red coloration on the stem 
  • Leave are not evergreen and will turn red/yellow in the fall
  • Young leaves can be red and hard to identify
  • Mature leaves can be very large and rounded

I've included a few more links that get into the details of identification.  But as long as you take your time in the forest and practice identification, you will pick up on the small differences and variations of this plant.  Happy Trails!


Read More »

Monday, May 15, 2017

Spring Break 2017: Day 3

Day 3: The Thinkery and The Austin Aquarium

After two days of hiking and playing in the water, it was time for a more relaxing day.  And what is more relaxing than herding children among other children. Off to the Thinkery and Austin Aquarium!


I was concerned with the traffic in Austin due to SXSW going on this whole time.  We had been avoiding it because our first two excursions were near the edge of the city, but now we need to cross the city.  No idea how we accomplished it, but we got across town.

First stop, The Thinkery!



The Thinkery was once the Austin Children's Museum.  It went through a remodel and a repurposing.  What a great space.  We had to wait in line to get in.  Spoiler Alert: Spring Break is their busiest time of the year.  But we got there early and only had to wait 10 minutes to get inside.  There are great features for all ages.  A light room, wax printing, gear room and even a maker space. However, be prepared for the water room.  Unwatched children are your enemy here as they can spray water everywhere.  So maybe bring backup clothes if your day requires travel elsewhere.  Really fun room though, kids get to play in the water.





After lunch, it was off to the Austin Aquarium.  So when you pull into the parking lot, you will be a little hesitant.  It's in this weird shopping center.  But don't judge it, its a really cool little aquarium.  you can feed the animals, including sharks.  Yes, you too can stick your hand in a tank and feed sharks. Lots of great tanks.  Take your time because they have some great little guys hiding in there.







All in all, it was a great trip.  I would do it again in the future, maybe get a cabin in the woods or go back to the RV park. I think a summer trip would be in order as I want to take the kids to Barton Pool.  Although its really cold, I think they would really enjoy it.  Until next time!

Read More »